Key Takeaways
- Each stage (an impeller paired with a diffuser) adds head in series, so total head is roughly the sum of the stage heads while flow stays the same through every stage.
- Small stacked impellers beat one big impeller because head tracks tip speed squared.
- Head is set by the hydraulics. Pressure isn’t.
- Inlet pressure plus closed-valve pressure has to stay below the pump’s maximum operating pressure, and that’s the limit most often missed on booster retrofits.
- Most field failures trace back to low flow, poor first-stage NPSH, dry running, worn clearances, or axial thrust.
Why One Impeller Runs Out of Head
A centrifugal impeller’s head comes from the Euler equation, and in practice it tracks the square of peripheral tip speed. So if a duty calls for 400 ft at 40 gpm, you could chase it with one huge impeller on a 2-pole motor. But you’d end up with a very low specific speed design, disk friction losses that climb steeply with diameter, and an efficiency number nobody wants to sign off on.
Vertical multistage pumps take a different route. They split the work across several small impellers running in series on one shaft, each one operating near a comfortable specific speed.
That’s the core idea, and everything else is about engineering the stack to survive real operating conditions.
What Happens Inside a Single Stage
In a radially split, vertical in-line design, each stage is an impeller plus a diffuser. The Hydraulic Institute’s summary of DOE pump definitions describes this RSV class (VS8 in ANSI/HI nomenclature) as a multistage pump where every stage consists of an impeller and a diffuser.
The impeller raises static pressure in its vane passages. It also throws liquid out at high absolute velocity. Diffuser vanes then slow that flow, converting velocity head into static pressure, and turn it inward to the next impeller’s eye.
So the second impeller starts with the first stage’s discharge as its “suction” and adds its own increment on top.
How the Grundfos CR Is Built Around That Stack
According to the Grundfos CR, CRI, CRN data booklet, the pump consists of a base and a pump head, with staybolts securing the chamber stack and sleeve between them. Liquid enters the base and climbs through the stages. Then it returns down the annular space between the chambers and the sleeve to the in-line discharge port.
Why should a maintenance team care? The base, sleeve, and staybolts see discharge pressure rather than suction pressure, and because the shaft seal sits in the pump head at the top of the stack, trapped air collects right where the seal faces need liquid.
Head Adds Up, Flow Doesn’t
Every stage handles the full flow, so stacking stages multiplies head, not capacity. As a simplified illustration, a stage making 30 ft at the duty point gives you about 300 ft with ten stages, or roughly 130 psi on cold water (psi = ft × SG ÷ 2.31). Real curves aren’t perfectly additive, and Grundfos fills gaps between stage counts with reduced-diameter impellers, noted in the CR type key.
That’s how one frame size can cover hundreds of pressure points.
Temperature changes the picture, though. Hotter water has lower specific gravity, so the same head reads as fewer psi, while rising vapor pressure eats into available NPSH. On boiler feed duty, both effects hit at once.
Speed Is the Other Lever
Since head scales with the square of speed, a VFD reshapes the whole curve. Drop speed 10 percent and shutoff head falls by about 19 percent. That’s why variable-speed builds like the Grundfos CRE variable-speed pumps we supply can hold a constant discharge setpoint while demand swings, instead of burning energy across a throttling valve. The DOE’s Improving Pumping System Performance sourcebook covers the energy lost to throttling and bypass control in detail.
It works the other way too. Within the Grundfos CR range, the CRNE-HS is a compact, high-speed single pump system built for high pressure, which is the tip-speed relationship put to work.
For existing fixed-speed units, an external drive from our industrial VFD drives lineup is usually the simplest retrofit path.
The Pressure Limit Most People Miss
Here’s where booster retrofits go wrong: Grundfos states that the actual inlet pressure plus the pressure the pump delivers must always stay below the maximum permissible operating pressure. Their booklet works an example: a pump rated for 232 psi that produces 139.2 psi against a closed valve can only accept about 92.8 psi at the inlet.
Now picture a building fed from a strong municipal main. Someone swaps in a pump with more stages for “more pressure,” and the closed-valve case pushes the casing past its rating. Connection type matters as well, since the same booklet rates smaller CR sizes at 232 psi with oval flanges but 362 psi with ANSI, clamp, or PJE connections.
Grundfos lists the CR range up to 50 bar (about 725 psi). Always check the specific model’s pressure and temperature chart rather than the range maximum.
Where the Stack Fails First
Multistage designs pack a lot of energy into a small liquid volume, so failure modes are fairly predictable.
Low Flow and Deadheading
As flow approaches zero, most of the shaft power ends up as heat in the liquid. Grundfos publishes a minimum flow rate, as a percentage of rated flow, that rises with liquid temperature and warns that running below it risks overheating. More stages means more power going into the same trapped water.
First-Stage NPSH
Only the first impeller sees true suction conditions.
Every stage after it is fed by the one before. Grundfos advises checking NPSHr at the highest possible flow rate, and that matters in parallel booster sets: when one pump trips, the remaining pump can run far out on its curve where NPSHr climbs. The Hydraulic Institute’s guidance on NPSH margin and pump operating regions explains why required margin increases as you move away from BEP.
Dry Running and Seal Damage
A mechanical seal running dry can be damaged quickly. Dry-run protection on the suction side is cheap insurance, and when a seal does fail, our mechanical seal solutions team can help diagnose and replace it.
Worn Internal Clearances
Neck ring wear lets each stage recirculate a little flow back to its own eye. One stage losing a few feet doesn’t sound like much. Spread it across twelve stages, though, and the pump misses its duty point while motor amps look close to normal.
Axial Thrust
Hydraulic axial thrust grows with stage count, and in standard close-coupled CR builds, the motor bearings carry it. That’s one reason Grundfos fits these pumps with a Grundfos-specified, heavy-duty motor, and swapping in a generic C-face motor without checking its bearing thrust rating tends to shorten bearing life.
Read PEI Ratings Carefully
In the U.S., RSV pumps fall under the DOE energy conservation standards for pumps, which cap the Pump Energy Index at 1.00. Multistage models are rated at a standardized stage count, and Grundfos notes PEI can’t be used to determine efficiency in a specific application. The North American CR 10, for example, shows a PEICL of 0.87 and a PEIVL of 0.48.
Useful for comparing models? Yes, but it’s no substitute for checking your actual duty point against the curve.
How We Support Vertical Multistage Pump Projects
At AMED-US, we work as an authorized Grundfos supplier for industrial, commercial, and municipal customers across the U.S., Latin America, and the Caribbean. Our Grundfos multistage pumps lineup includes the CR-H, CRN-H, CRE-H, and CRNE-H models and packaged boosters like the Grundfos Hydro MPC booster system. Browse other brands in our vertical multistage pumps category.
Selection is only half the job. Our pump installation and repair services include testing and commissioning to verify operation at the best efficiency point, backed by licensed engineers in Miami. Chasing a pressure complaint in a water and wastewater system? Start with our guide on low water pressure and booster pump systems.
Get the Right Multistage Pump for Your Pressure Duty
Not sure how many stages your duty really needs, or whether your inlet pressure leaves enough room under the casing rating? Contact AMED-US today with your flow, head, suction conditions, and fluid temperature, and we’ll help you pin down the right Grundfos model, motor, and controls.
FAQ
How much pressure can a vertical multistage pump produce?
It depends on stage count, speed, and the casing’s pressure rating, and while Grundfos lists its CR range up to 50 bar (about 725 psi), each model has its own pressure and temperature limits.
Can a vertical multistage pump run against a closed valve?
Only very briefly. With no flow, shaft power heats the trapped liquid. Grundfos specifies a minimum flow rate that rises with liquid temperature to prevent overheating.
What’s the difference between head and pressure on a multistage pump?
Head is the energy added per unit weight of liquid and doesn’t depend on density. Pressure equals head times specific gravity divided by 2.31 (in feet and psi), so the same pump shows lower pressure on hot water than on cold.
Why does a multistage pump lose pressure over time?
Worn neck rings and impellers increase internal recirculation at every stage. Those small losses add up across the stack. Air entrainment, low NPSH, and a partly closed suction valve can cause similar symptoms.
Do Grundfos CR pumps meet DOE efficiency standards?
Models within the DOE scope have to, since the RSV class is covered by rules that cap PEI at 1.00, and Grundfos publishes PEI values for its North American CR models, such as 0.87 PEICL for the CR 10.